USB-QC30R2

USB-QC30R2 programming cable is simulated into a traditional serial port (commonly known as COM port) through the USB port of the computer, so that all kinds of existing programming software, communication software and monitoring software can be used to convert the status of the LED on the box to indicate the receiving and receiving of data. This cable is suitable for Mitsubishi Q series PLC

Characteristics and Technical Indicators

  • Operating System: Windows XP/Windows 2000 
  • Support Programming Software Version: Unlimited Version 
  • Each PC only supports one USB programming cable.

Usage

  1. USB-QC30R2 programming cable needs to install a USB driver to use.
  2. After the installation of driver, COM corresponding to USB-QC30R2 programming cable will appear in the device manager of Windows.
  3. In normal use, first insert the cable into the computer USB port, and then insert the six-pin round port into Q_PLC
  4. Open Resource Manager View COM slogan, click My Computer Control Panel Management Tool Computer Management with mouse Logic Device Manager Port (COM and LPT) Prolific USB-to-Serial Comm (COMx) This COMx is the COM slogan for USB programming cables
  5. Open the programming software GX DEVELOPER, Open On-line Transmission Settings DEVELOPER.Double-click \Serial Port (USB) to set COM slogan and set baud rate to
    9600 can communicate

Wire

Drive

usb-qc30r2 drive

USB-SC09-FX

USB-SC09-FX is a programming cable which provides serial connection and RS422 signal conversion through the USB interface. Under the control of the driver running in the computer, the USB interface of the computer is simulated as a traditional serial port (commonly known as COM port), so that the existing programming software, communication software and monitoring software are used. The working power source of this cable is from USB port. It is no longer powered by the programmable port of PLC. The two-color light emitting diode on the conversion box indicates the receiving and receiving status of the data. 

USB-SC09-FX programming cable for Mitsubishi FX2N/FX1N/FX0/FX0N/FX0S/FX1S/FX3U… The FX series PLC of MD8F circular socket can replace FX-232AW communication module and support maximum communication distance of 2 km.

For Mitsubishi A series PLC and all FX series PLC (including old product FX2/FX2C), please select the programming cable USB-SC09 which supports A series and FX series.

Characteristics and Technical Indicators

USB-SC09-FX Operating System: Win2000/WinXP/Win7/Win10
Programming Software Version Supporting USB-SC09-FX: FXGP/WINV1.0, GPP_V4.0, GX_Developer_V8.0 and above
Fully compatible with USB_V1.1 and USB_CDC_V1.1 specification
USB Bus Power Supply, Consumption Current About 50mA
Baud rate: 300 bps~1 Mbps standard baud rate automatic adaptation
Support UART data format: data bits: 5, 6, 7, 8, stop bits: 1, 2, check bits: odd/even/no parity
Supports long-distance communication. Maximum communication distance is 2 km (9600 bps)
Each PC only supports one USB programming cable
Working temperature: -20~+75
Cable length: 2.5 m, color: black

How to use usb-sc09

USB-SC09-FX programming cable needs to install USB device drivers to use.
When the driver is installed, the COM port corresponding to the USB-SC09-FX programming cable will appear in the device manager of Windows. It is only necessary to select the COM port in the programming software or other application software. The other communication parameters are set by default.

USB-SC09 Pinout

sc09-fx cable pinout
sc09-fx cable pinout

USB-SC09 Cable

USB-SC09

USB-SC09-FX

SC09

USB-SC09 Cable Driver

usb-sc09-fx/usb-sc09 driver Download

Some WIN 7 Ultimate operating system Driver not integrate well, this folder serenum.sys copied to C: \WINDOWS\system32\under drivers, you can reinstall the driver CH341.